Showing results: 541 - 555 of 843 items found.
-
Proteus
Proteus Virtual System Modelling (VSM) blends mixed-mode SPICE simulation with world leading fast microcontroller simulation. It enables rapid prototyping of both hardware and firmware designs, in software! Design, Test and Debug your embedded projects in the Proteus electronic circuit simulator before a physical prototype is ordered. Agile development for the embedded systems workflow.
-
COMBI519 -
HT Italia Srl
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
COMBI521 -
HT Italia Srl
COMBI521 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
EASYTEST -
HT Italia Srl
EASYTEST carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
IPMDS40 -
Technology Research Corp.
- Intelligent Power Management System- 9 - 20 Amp Single Outlets- Automatic Single Phase Load Balancing- Automatic Load Shedding based on priority rating- 40 Amp Mil Spec Input and Output Connector- Easy Access Circuit Breakers- Phase Over Current Protection- Low Voltage Warning- Built In Press to Test
-
HDYZ -
HD Power Test Equipment Co.ltd
HDYZ Transformer on-load tap changer Tester is a unique moving part that is connected with the circuit of the transformer, It is essential to test the on-load tap changer of action sequence and switching time.HDYZ Transformer On-load Tap Changer Tester is mainly applied to measure the transient waveform, transient time, transient resistance value, three-phase synchronization of transformer on-load tap-changers.
-
CAT Advanced Series -
Amperis sl
Description The Advanced CAT Series Analyzers and Timers are stand-alone or PC-controlled digital instruments for circuit breaker status evaluation. Timing channels record arc closing and opening, resistance and auxiliary contacts. The main contact channels can also measure the resistance value of pre-insertion resistors (if present in the breaker). The advanced CAT series records graphs of the opening and closing coil currents and the movements of the moving parts of the high and medium voltage circuit breaker. Test results are printed on the 112 mm (4.4 inch) thermal printer (optional accessory) in tabular and graphical form. The advanced CAT series provides easy selection of different operating modes:
-
ETI Precision
The ETI adjustable test stab set may be used with your high-current circuit breaker testers to maximize efficiency and convenience for testing multiple breakers. Our stab system allows your technicians to test breakers in-place and avoid jacking breakers up or down for testing. By combining mobility and flexibility into one simple system, this stab set is a proven improvement over conventional designs. The components in the adjustable stab set are made of 120 pounds of 110 copper.
-
Educated Design & Development, Inc.
Flexing Tests: On flexible cables (or cords sets with fitted plugs), electric tools or hand lamps. Meets requirements of standards such as IEC 60335, IEC 60227, IEC 60745 and UL745. This product is for continuous bending tests of cables or cord sets fitted with plugs. The model F39 allows the simultaneous testing of two samples in it's standard version. This not only allows for substantial time savings, but also allows for the testing current circuits to be simplified by looping through the cables.
-
783466-01 -
NI
51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module - The NI‑9260 is an instrument-grade dynamic signal generator for testing the audio components and capabilities of consumer electronic devices and providing excitation in structural test applications. Unlike sound card-based solutions, the NI‑9260 can be deployed quickly and recalibrated to guarantee long-term measurement repeatability and decreased test time. It also features ±30 V overvoltage protection and short circuit protection.
-
783467-01 -
NI
51.2 kS/s/ch Simultaneous, 3 Vrms, 2-Channel C Series Voltage Output Module - The NI‑9260 is an instrument-grade dynamic signal generator for testing the audio components and capabilities of consumer electronic devices and providing excitation in structural test applications. Unlike sound card-based solutions, the NI‑9260 can be deployed quickly and recalibrated to guarantee long-term measurement repeatability and decreased test time. It also features ±30 V overvoltage protection and short circuit protection.
-
4101 IN -
Standard Electric Works Co., Ltd
● Measures Insulation Resistance, voltage (AC-DC) measurements.● Automatic hold facility.● Continuity test with a short circuit current of minimum 200mA.● Energy conservation is feature.● EnerSave™ limits the test duration to about 10 Seconds to save energy.● No moving parts. All calibration are saved internally in a non volatile memory.● Easy calibration at any facility around the world.● Low cost maintenance, calibration, and ownership.● Complies to all the latest regulations, including UK.
-
BK2021 -
BaKo Co., Ltd
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
Thermo Fisher Scientific Inc.
Identify and help correct ESD and latch-up susceptibility issues on sensitive integrated circuit components prior to full-scale production with the Thermo Scientific™ MK.2-SE ESD and Latch-Up Test System. The MK.2-SE test system provides advanced capabilities to test high pin count IC devices to Human Body Model (HBM) and Machine Model (MM) ESD standards. The system’s pulse delivery design addresses wave form hazards such as trailing pulse and pre-discharge voltage rise, and performs Latch-Up testing per the JEDEC EIA/JESD 78 Method.
-
Wewon Environmental Chambers Co, Ltd.
In Wewon, We have 2 powerful Vibration Testing Equipment. The Vibration Testing Equipment A is : EV210H0808VCSusb-E; The Vibration Testing Equipment B is: EV232H0809VCSusb-E. Technical parameters as below blank forms mentioned, The mainly difference is Sine Excitation Force, Frequency Range, Vibration Table’s size. Application for Vibration Test Equipment : The vibration test is to inspire or impact a part or device to see how it reacts in a real environment. The application of vibration test is very extensive, from the circuit board, aircraft, ships, rockets, missiles, automobiles and household appliances and other industrial products.
